The trunk on the hood Land Rover Defender.

Material-aluminum.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Eight-point aluminum trunk.
Gives an ascetic car a more determined, menacing look.

On the trunk you can pin sand trucks, gardening tools, lights, pneumatic beeps.

• Length of 2.80 meters,
• Width of 1.40 meters,
• Weight 60 kg,
• Load capacity up to 0.5 tons.

In one of the photos, we ran over the trunk support of a Toyota LAND CRUISER 105 to demonstrate its (support) strength.

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Eight-point aluminum trunk-platform.
Gives an ascetic car a more determined, menacing look.

This expedition trunk is very convenient.
In the trunk, if necessary, you can walk.
With a limited height of the garage, the trunk allows you to enter the garage without any problems.
The absence of the upper tier reduces weight and air resistance at speed, which provides less fuel consumption, less noise.

On the trunk you can pin sand trucks, gardening tools, lights, pneumatic beeps.

• Length of 2.80 meters
• Width of 1.40 meters
• Weight 60 kg
• Load capacity up to 0.5 tons

In one of the photos, we ran over the trunk support of a Toyota LAND CRUISER 105 to demonstrate its (support) strength.

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Six-point aluminum trunk-platform.
Gives an ascetic car a more determined, menacing look.

This expedition trunk is very convenient.
In the trunk, if necessary, you can walk.
With a limited height of the garage, the trunk allows you to enter the garage without any problems.
The absence of the upper tier reduces weight and air resistance at speed, which provides less fuel consumption, less noise.

On the trunk you can pin sand trucks, gardening tools, lights, pneumatic beeps.
It has the ability to mount a HiJack type Jack, additional lights.

• Length of 2.00 meters
• Width of 1.40 meters
• Weight 50 kg
• Load capacity up to 0.5 tons
• The bottom is covered with an aluminum strip

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Six-point trunk.

It can be equipped with a fixture for lighting equipment, lighting equipment itself, fixing rails, shantzevogo tool.
In addition to the expedition trunk, a ladder can also be installed on the car.
It has the ability to mount a HiJack type Jack, additional lights.

• Length of 2.00 meters
• Width of 1.40 meters
• Weight 50 kg
• Load capacity of up to 0.6 tons (so much to load the expedition trunk is still not worth it-the design will withstand more, and the roof of the car is unlikely.)
• The bottom is covered with an aluminum strip

In one of the photos, we ran over the trunk support of a Toyota LAND CRUISER 105 to demonstrate its (support) strength.
Expedition trunk supports are universal: they can be used for setting arcs.

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Six-point aluminum trunk-platform.
Gives an ascetic car a more determined, menacing look.

On the trunk you can pin sand trucks, gardening tools, lights, pneumatic beeps.
They have the ability to mount a HiJack type Jack, additional lights.

This expedition trunk is very convenient.
On the trunk, if necessary, you can walk.
With a limited height of the garage, the trunk allows you to enter the garage without any problems.
The absence of the upper tier reduces weight and air resistance at speed, which provides less fuel consumption, less noise.

• Length of 1.60 meters
• Width of 1.40 meters
• Weight 40 kg
• Load capacity up to 0.5 tons
• The bottom is covered with an aluminum profile

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Six-point aluminum trunk.

On the trunk you can pin sand trucks, gardening tools, lights, pneumatic beeps.
It has the ability to mount a HiJack type Jack, additional lights.

• The equipment includes platforms for the searchlights of the front and rear optics, loops for railings.
• Length of 2.00 meters
• Width of 1.40 meters
• Weight 55 kg
• Load capacity up to 0.5 tons (do not overdo it, or the body racks will be folded)
• The bottom is covered with an aluminum strip

In one of the photos, we ran over the trunk support of a Toyota LAND CRUISER 105 to demonstrate its (support) strength.

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

The trunk is expedition aluminum.

Suitable for all pickups.

It has the ability to mount a HiJack type Jack, additional lights.
The bottom is covered with an aluminum strip.
In one of the photos, we ran over the trunk support of a Toyota LAND CRUISER 105 to demonstrate its (support) strength.

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Six-point aluminum expedition trunk.
Solidly made, beautifully painted, load-bearing, elegant, functional.

On the one hand, it is equipped with a fastener for the Hajek, on the other-for the ladder.

The trunk is equipped with platforms for the searchlights of the front and rear optics, loops for the rails. The trunk is installed on the gutter.

• Dimensions 200x125 cm.
• Weight 35 kg.

In one of the photos, we ran over the trunk support of a Toyota LAND CRUISER 105 to demonstrate its (support) strength.

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

The trunk aluminum eight-point.
Solidly made, beautifully painted, load-bearing, elegant, functional.

On the one hand, it is equipped with a fastener for the Hajek, on the other-for the ladder.

The trunk is equipped with platforms for the searchlights of the front and rear optics, loops for the rails. The trunk is installed on the gutter.

• Dimensions 230x125 cm.
• Weight 45 kg.

In one of the photos, we ran over the trunk support of a Toyota LAND CRUISER 105 to demonstrate its (support) strength.

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

The eight-point trunk-platform.

The absence of the upper tier reduces weight and air resistance at speed, which provides less fuel consumption, less noise.

This trunk is very convenient.
If necessary, you can walk on it.
With a limited height of the garage, the trunk allows you to enter the garage without any problems.

• The weight of the trunk is 25 kg.

In one of the photos, we ran over the trunk support of a Toyota LAND CRUISER 105 to demonstrate its (support) strength.

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

The expedition trunk is suitable for Toyota Land Cruiser Prado 120.
The aluminum trunk is mounted on standard rails in 20 minutes.

It has the ability to mount a HiJack type Jack, additional lights.

• Length of 1.18 metres
• Width of 1.07 meters
• Weight 18 kg
• Load capacity up to 0.5 tons
• The bottom is covered with an aluminum strip
• The aluminum trunk is made without space under the hatch.

Recommended load up to 60 kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted and painted with a zinc layer-a thermally active black powder paint. ground and second.

Expedition trunk for Toyota Land Cruiser Prado 150.
The trunk is installed instead of standard rails.

It has the ability to mount a HiJack type Jack, additional lights.

• The weight of the trunk is 25 kg.
• Size 1840*1126 mm.
• The bottom is covered with an aluminum strip

The aluminum trunk is made without space under the hatch.

Recommended load up to 60 kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Six-point trunk expedition " Lux " aluminum.

The trunk is installed in the place of standard rails, on steel rails that are supplied as a set.

• Length of 2.20 meters
• Width of 1.15 metres
• Weight 35 kg
• Load capacity up to 0.5 tons (just do not overdo it, and then add up the body racks)
• The bottom is covered with an aluminum strip

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Six-point aluminum trunk with no space under the hatch.

Installed in place of railings

It has the ability to mount a HiJack type Jack, additional lights.

• Length of 2.20 meters
• Width of 1.15 metres
• Weight 35 kg
• Load capacity up to 0.5 tons (just do not overdo it, and then add up the body racks)
• The bottom is covered with an aluminum strip

The trunk is mounted on supports, the strength of which is shown in one of the photos: after we ran over it with the TLK 105 wheel, the shape remained the same.

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Aerodynamic aluminum trunk with no space under the hatch.

The trunk is installed in the place of standard rails, on steel rails.

It has the ability to mount a HiJack type Jack, additional lights.

• Length of 2.20 meters
• Width 1,165 meters
• Weight 38 kg
• Load capacity up to 0.5 tons
• The bottom is covered with an aluminum strip

The trunk is equipped with platforms for the searchlights of the front and rear optics.

The aluminum trunk is made without space under the hatch.

Recommended load up to 80kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Expedition aluminum six-point.
Installed in place of the rails.

It has the ability to mount a HiJack type Jack, additional lights.
The trunk is equipped with platforms for the searchlights of the front and rear optics, loops for the rails.

Length of 2.20 meters
Width of 1.15 metres
Weight 35 kg
The bottom is covered with an aluminum strip
The trunk is mounted on supports, the strength of which is shown in one of the photos: after we ran over it with the TLK 105 wheel, the shape remained the same.

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint

Six-point aluminum trunk.
Installed in place of the rails.

The absence of the upper tier reduces weight and air resistance at speed, which provides less fuel consumption, less noise.


This trunk is very convenient.
In the trunk, if necessary, you can walk. With a limited height of the garage, the trunk allows you to enter the garage without any problems.

The trunk is equipped with platforms for the searchlights of the front and rear optics, loops for the rails.

• Length of 2.20 meters
• Width of 1.15 metres
• Weight 25 kg
• The bottom is covered with an aluminum strip

The trunk is mounted on supports, the strength of which is shown in one of the photos: after we ran over it with the TLK 105 wheel, the shape remained the same.

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Six-point aluminum trunk.

It has the ability to mount a HiJack type Jack, additional lights.
The bottom is covered with an aluminum strip.

The trunk is mounted on supports, the strength of which is shown in one of the photos: after we ran over it with the TLK 105 wheel, the shape remained the same.

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Six-point aluminum expedition trunk.

It has the ability to mount a HiJack type Jack, additional lights.

The trunk is equipped with platforms for the searchlights of the front and rear optics, loops for railings.

• Weight 42 kg
• The bottom is covered with an aluminum strip

It is made in 2 versions:
- No space under the hatch
- With a place under the hatch

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Four-point aluminum trunk.
Does not require drilling of the roof.

It is made of aluminum, the girths of the supports are made of stainless steel.

• Dimensions 140 cm x 155 cm.
• Weight 20 kg.

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Four-point aluminum trunk.
Does not require drilling of the roof.

It is made of aluminum, the girths of the supports are made of stainless steel.

• Dimensions 125 cm x 155 cm.
• Weight 20 kg.
• The maximum height from the roof to the extreme point of the side is 20 cm.

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Four-point aluminum trunk.
It is also suitable for the 2015 Toyota HILUX.

Does not require drilling of the roof.

It is made of aluminum, the girths of the supports are made of stainless steel.

• Dimensions 125 cm x 155 cm.
• Weight 20 kg.
• The maximum height from the roof to the extreme point of the side is 20 cm.

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Expedition four-point aluminum trunk.
It is also suitable for the 2015 Toyota HILUX.

Does not require drilling of the roof.

It is made of aluminum, the girths of the supports are made of stainless steel.

• Dimensions 115 cm x 148 cm.
• Weight 20 kg.
• The maximum height from the roof to the extreme point of the side is 20 cm.

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Expedition four-point aluminum trunk.
Suitable for double cab (Crew Max).

Does not require drilling of the roof.

It is made of aluminum, the girths of the supports are made of stainless steel.

• Dimensions 135 cm x 160 cm.
• Weight 20 kg.

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.

Four-post aluminum trunk with spoiler.
Aerodynamic design.

Suitable for double cab (Crew Max).

The expedition trunk is made of aluminum, the girths of the supports are made of stainless steel. Does not require drilling of the roof.

• Dimensions 135 cm x 160 cm.
• Weight 20 kg.

Recommended load up to 50kg for cross-country driving. You can load more, but drive more carefully. These recommendations are given in order not to damage the body geometry. And remember that the center of gravity goes up a lot, and the car is more likely to tip over on its side, on the same rough terrain and high speeds.

All KDT products are sandblasted, painted with a zinc primer and a second layer-a thermoactive black powder paint.